Zenoah SRTZ2500 Manual do Utilizador

OWNER/OPERATOR MANUALSHORT REACH TRIMMER848-A2A-93A1 (501)SRTZ2500The engine exhaust from this productcontains chemicals known to the Stateof Californ

 10 Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting a

• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap

 12 5. For safe operation HANDLING FUEL1. The engine of the RedMax product is designedto run on a mixed fuel which contains highlyflammable gasolin

MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged with the g

 14 6. Set upSE4 ATTACHING THE TRIMMING MECHANISM (SE4)1. Remove the cap on the end of the main pipe.2. Remove the screw screwed into the end of the

RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1• Exhaust emission are controlled by thefundamental engine parameters andcomponents(eq., carburation, ignit

 16 7. Fuelagain for at least one minute. As someoils may be difficult to agitate dependingon oil ingredients, sufficient agitation isnecessary for

STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Rest the unit on a flat, firm place. Keep thecutting head off the groun

 18 8. Operation STOPPING ENGINE (OP3)1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP po

handling can cause accidents which may inturn lead to serious injury or death. For thisreason, you should always be careful to followthe following in

INFORMATION This machine is equipped with an Overload CancellationMechanism. When the cutting blades have got into metal wires or thosetwigs difficult

 20 9. Maintenance BLADES (MA1)•When refilling the tank or resting, it is often agood idea to use the time to oil the cuttingblades.• If a gap exis

QUICK TIPIf the blades become so worn down that it is nolonger possible to eliminate the gap between them,you should contact the authorized RedMaxserv

 22  SPARK PLUG• Starting failure and mis-firing are often causedby a fouled spark plug. Clean the spark plug andcheck that the plug gap is in the

9. Maintenance INTAKE AIR COOLING VENT•Never touch the cylinder, muffler, or sparkplugs with your bare hands immediately afterstopping the engine. T

11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filter ➞

Jun. 200312. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does

12. Parts list  26 Fig.1 DRIVE UNIT SRTZ2500 (S/N 000000 and up)Fig.2 CUTTING UNIT SRTZ2500 (S/N 000000 and up)

Fig.2 CUTTING UNIT SRTZ2500 (S/N 000000 and up)Fig.1 DRIVE UNIT SRTZ2500 (S/N 000000 and up)Key# Description Part Number Q'ty1PIPE COMP. T3075-

Fig.3 ENGINE UNIT SRTZ2500 (S/N 50100000 and up) 28 12. Parts list

Fig.3 ENGINE UNIT SRTZ2500 (S/N 50100000 and up) 29 Key# Description Part Number Q'ty1 CYLINDER 4810-12111 12 GASKET, base 4810-12210 13 BOLT

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMa

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093©Printed in Japan

2. Specifications SRTZ2500Overall size(LxWxH)························································ 67.9(1725)x9.8(250)x12.2(310) in(mm)Dry weight

 5 (1) Read owner's manual before operatingthis machine.(2) Wear head, eye and ear protection.(3) Handling this machine improperlycould result

 6 For safe operation and maintenance, symbols arecarved in relief on the machine. According to theseindications, please be careful not to take a mi

5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this manual

 8 b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview

BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area into w