Zenoah BCX2600S Manual do Utilizador

OWNER/OPERATOR MANUALBRUSHCUTTERST3032-93110 (004)BCX2600SThe engine exhaust from this productcontains chemicals known to the Stateof California to ca

10 Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting at

• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap

12 5. For safe operationtank of the unit in any place where there is aboiler, stove, wood fire, electrical sparks,welding sparks, or any other sourc

MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged with the g

14 6. Set upSE5 INSTALLING CUTTING HEAD (SE5)1. While locking the gear shaft, by inserting thesupplied tool into the upper holder on the gearbox, l

RECOMMENDED OIL TYPEUsing the proper type and weight of oil in thecrankcase is extremely important. Check the oilbefore each use and change the oil

16 Old fuel is usually the main reason for the unit notrunning properly. Be sure to use fresh, clean,unleaded fuel.Alcohol-blended fuel absorbs mois

STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Check the oil level in crankcase (See OILLEVEL at p.22).2. Fill the f

18 8. Operation2. Overchoking can make the engine hard to startdue to excess fuel. When the engine failed tostart after several attempts, open the c

CUTTING WORK (LINE HEAD USAGE)1. Always wear eye protection such as safetygoggles. Never lean over the rotating cuttinghead. Rocks or other debris c

20 9. Maintenance REFILLING TRIMMING LINE1. For replacement line, use a diameter of .095in(2.4mm). The spool is capable for a line upto27ft(8 m)on

on the housing, press the cap against thehousing until it clicks.• Make sure that the engine has stopped and iscool before performing any service to t

22  OIL LEVELTo prevent extensive engine wear and damageto the unit, always maintain the proper oil levelin the crankcase. Never operate the unit w

9. MaintenanceChange the oil as follow:1. Remove the oil fill plug/dipstick.2. Pour the oil into a container by tipping the unit toa vertical position

24 9. MaintenanceMA146. While looking in the spark plug hole, pull thestarter rope slowly and bring the piston to the topposition. Check that both r

9. Maintenance SPARK PLUG• Starting failure and mis-firing are often causedby a fouled spark plug. Clean the spark plug andcheck that the plug gap is

26 9. Maintenance SPARK ARRESTER• The muffler is equipped with a spark arrester toprevent red hot carbon from flying out of theexhaust outlet. Peri

9. Maintenanceorder to be able to view the upper part of thecylinder.• If waste gets stuck and causes blockage aroundthe intake air cooling vent or be

28 10. Cleaning and storage CLEANINGAlways turn off your trimmer before you clan orperform any maintenance on it.Use a small brush to clean off the

Under growthHeavy weedsLight weedsGrassSaw blade6298-11213 6298-15243 6298-142438-teeth blade 4-teeth bladeNylon line headCUTTER APPLICATIONCHART11. O

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

30 11. Optional blade usageChange the loop handle to the J-handle for safeoperation. (OPT4)(1) Bracket: 3583-14101(2) J-handle: 6367-14200 STARTING

11. Optional blade usage OPERATION1. Check the bolt to fasten the blade and be surethe bolt has no fault, and no abrasion.2. Be sure that the blade a

2. How you can reduce the chance of kick out:a. Recognize that kick out can happen. Byunderstanding and knowing about bounce,you can help eliminate th

MAINTENANCEBLADE• Check the blade and the fasteners forlooseness, cracking, or bending.• Check the cutting edges and reform with a flatfile.Point (O

34 12. Troubleshooting guidePROBLEMEngine will not start.Engine will not idle.Engine will not accelerate.Engine lacks power to stallswhen cutting.En

13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

13. Parts list 36 Fig.1 CUTTER GROUP BCX2600S

Fig.1 CUTTER GROUP BCX2600SKey# Description Part Number Q'ty1 PIPE-COMP T3002-12100 12 SHAFT 3520-12212 13 GEARCASE-ASSY T3002-13001 14 • GEARCA

Fig.2 ENGINE GROUP BCX2600S38 13. Parts list

39 Fig.2 ENGINE GROUP BCX2600SKey# Description Part Number Q'ty1 HEAD&BOX 182141 12 VALVE 181040 23 SPRING VALVE 181038 24 RETAINER, valve

2. Specifications BCX2600SOverall size(LxWxH)······················································ 72.5(1840)x12.5(320)x13.6(345) in(mm)Dry weight w

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL BCX2600S UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), TH

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

(1) Read owner's manual before operatingthis machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4)Keep all children, bystanders

6 For safe operation and maintenance,symbols are carved in relief on the machine.According to these indications, please becareful not to take a mist

7 5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this ma

8 b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview o

BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area into w